Chrysler Pacifica:

2007 Pacifica

You are not logged in.

#1 2/28/2012 8:00 PM

Ponch
New member
Registered: 2/28/2012
Posts: 1

2007 Pacifica

Need a picture of motor mounts on a 2007 Pacifica 4.0

Chrysler Pacifica Recalls, TSBs and Service Information >> ALLDATA

Offline

 
Sponsored Links
ALLDATAdiy.com

The Leading Source of Professional Diagnostic and Repair Information.

#2 2/29/2012 12:40 AM

TechHelp2
Administrator
Registered: 11/24/2009
Posts: 1299

Re: 2007 Pacifica

I have found pictures and removal and installation procedures for all three mounts on the engine, they are from the Alldata information website, they are listed below.

I hope they help you.


https://www.realworldautomotive.com/forums/uploads/thumbs/174_1310039331.jpg

Support engine assembly with a floor jack so it will not rotate.
Remove the air cleaner element housing.
Remove the upper engine mount bolts from the inner frame rail.
Remove the upper engine mount bolts from the engine.

Installation:

Support the engine assembly with a floor jack.
Properly position the upper engine mount and install the retaining bolts.
Tighten the bolts attached to the intake manifold to 54 Nm (40 lbs. ft.) .
Tighten the bolts attached to the inner frame rail to 68 Nm (50 lbs. ft.) .
Remove the jack used to support engine assembly.
Install the air cleaner element housing.

https://www.realworldautomotive.com/forums/uploads/thumbs/174_1310039351.jpg

Removal:

Disconnect the negative battery cable.
Remove engine cover.
Remove radiator cooling fan assembly.
Raise and support the vehicle.
Remove both of the engine mount to cradle nuts.
Lower the vehicle.
Connect the engine support fixture and support engine weight.
Remove the engine mount bolts and remove mount.

Installation:

Install engine mount to bracket. Tighten nut to 101 Nm (75 lbs. ft.) .
Install left mount to the engine block. Tighten bolts to 54 Nm ( 40 lbs.ft.) .
Lower vehicle.
Remove the engine support fixture.
Raise and support the vehicle.
Install both of the engine mount to cradle nut. Tighten nut to 101 Nm (75 lbs. ft.) .
Lower vehicle.
Install radiator fan assembly.
Install the engine cover.
Connect the negative battery cable.


https://www.realworldautomotive.com/forums/uploads/thumbs/174_1310061541.jpg

Removal:

Disconnect the negative battery cable.
Raise and support the vehicle.
Remove both of the engine mount to cradle nuts.
Lower the vehicle.
Connect the engine support fixture and support the engine weight.
Raise and support the vehicle.
Remove the right mount bracket bolts 
Remove the engine mount top nut.
Remove the engine mount plate and engine mount.


Installation:

Install the engine mount and plate.Tighten bolts to 54 Nm (40 lbs. ft.) .
Install the engine mount upper nut. Tighten nut to 101 Nm (75 lbs. ft.) .
Install right engine mount bracket bolts. Tighten bolts to 54 Nm (40 lbs. ft.) .
Lower the vehicle.
Remove the engine support fixture.
Raise and support the vehicle.
Install both lower engine mount to cradle nuts. Tighten nuts to 101 Nm (75 lbs. ft.) .
Lower vehicle and connect the negative battery cable.


realworldautomotive.com
car and truck information like nowhere else
Chrysler Pacifica Recalls, TSBs and Service Information >> ALLDATA

Offline

 
E-mail Page
Print Page
Save or Share Information
ALLDATAdiy.com is the leading source of factory diagnostic & repair information specific to your car.

Powered by PunBB
Copyright © 2007-  RealWorldAutomotive.com

Save or Share Automotive Information
Custom Search